Crucial MTFDDAT128MBF-1AN12ABYY Fiche technique Page 1

M600 mSATA NAND Flash SSDMTFDDAT128MBF, MTFDDAT256MBF, MTFDDAT512MBFFeatures• Micron® 16nm MLC NAND Flash• RoHS-compliant package• SATA 6 Gb/s interfa

EnduranceEndurance for the SSD can be predicted based on the usage conditions applied to thedevice, the internal NAND component cycles, the write ampl

Electrical CharacteristicsEnvironmental conditions beyond those listed may cause permanent damage to the de-vice. This is a stress rating only, and fu

Dynamic Write AccelerationDynamic write acceleration optimizes SSD performance for typical client-computingenvironments, where WRITE operations tend t

Adaptive Thermal MonitoringThe device features adaptive thermal monitoring. While most host computers exhibitoperating environments that keep an SSD r

TCG/Opal SupportTable 12: TCG/Opal Support ParametersProperty Supported? CommentsTCG Storage SpecificationsOPAL: TCG Storage Security SubSystemClassSp

Table 12: TCG/Opal Support Parameters (Continued)Property Supported? CommentsACK/NACK Support Not Supported Session reliabilityAsync Support Not Suppo

Table 12: TCG/Opal Support Parameters (Continued)Property Supported? CommentsByte Table Access GranularityMandatory Write Granularity 1 TPer enforces

Table 12: TCG/Opal Support Parameters (Continued)Property Supported? CommentsTCG Storage Silo Supported –Other than Probe and TCG Storage Silo Not Sup

Device IDTable 13: Identify DeviceSee Note 1 for setting definitionsWord Bit(s) Setting Default Value Description0 General configuration bit-significa

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description49 Capabilities15–14 F 00b Reserve

Part Numbering InformationMicron’s M600 SSD is available in different configurations and densities. The chart below is a comprehensive listof options

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description62 ()X 0000h Obsolete63 15–11 F 00

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description69 F Additional Supported15 F 0b 1

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description76 Serial ATA capabilities15 F 1b

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description79 Serial ATA features enabled15–9

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description82 Command set supported15 X 0b Ob

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description84 Command set/feature supported e

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description86 Command set/feature enabled.15

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description88 0b Ultra DMA modes15 0b Reserve

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description106 Physical sector size/logical s

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description120 Commands and feature sets supp

General DescriptionMicron’s solid state drive (SSD) uses a single-chip controller with a SATA interface onthe system side and eight channels of Micron

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description161 X 0000h 0000h0000h 0000h0000h

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description214 (O) NV Cache Capabilities15–12

Table 13: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description234 (O)F 0001h Minimum number of 5

CommandsTable 14: Supported ATA Command SetSee ACS-3 standard for command detailsCommand Name Command Code (hex)AMAC-GET NATIVE MAX ADDRESS EXT 78h/00

Table 14: Supported ATA Command Set (Continued)See ACS-3 standard for command detailsCommand Name Command Code (hex)SECURITY DISABLE PASSWORD F6hSECUR

Table 14: Supported ATA Command Set (Continued)See ACS-3 standard for command detailsCommand Name Command Code (hex)WRITE UNCORRECTABLE EXT 45hM600 mS

ComplianceMicron SSDs comply with the following:• RoHS “green”• CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003• FCC: CFR Ti

References• Serial ATA: High-speed serialized AT attachment, Serial ATA working group, availableat www.sata-io.org• SATA 3.2 GOLD• ATA-8 ACS3 (T13/216

Revision HistoryRev. E – 3/15• Updated table 12: TCG/Opal Support Parameters in TCG/Opal Support• Updated table 13: Identify Device in Device ID• Upda

Logical Block Address ConfigurationThe drive is set to report the number of logical block addresses (LBA) that will ensuresufficient storage space for

Physical ConfigurationProduct mass: 10 grams MAXPhysical dimensions conform to the applicable form factor specifications as listed inthe figure below.

Table 2: mSATA Package DimensionsDensity (GB) W L A B C Unit128 29.85 50.80 2.40 1.00 1.35 mm256512Note:1. Dimension values in millimeter per SERIAL A

Table 3: Signal Assignments (Continued)Primary Side Secondary SidePin # Signal Name Description Pin # Signal Name Description37 GND Ground 38 Reserved

PerformanceMeasured performance can vary for a number of reasons. The major factors affectingdrive performance are the capacity of the drive and the i

ReliabilityMicron’s SSDs incorporate advanced technology for defect and error management.They use various combinations of hardware-based error correct